Hello
Card front: Place your card with the fold at the left. Cover the card with Colorist white/black tiny dots paper (from the floral border sheet). Cut a 4 5/8”x6” Colorist pink dots paper and mat on black with 1/16” borders. Cut a 4 5/8”x3/4” Colorist black/white dots paper and glue it across the pink paper, 3/8” from the bottom. Glue a 4 5/8”x1/4” Silver Linen paper even with the bottom of the black/white dots paper. Glue the matted pink paper centered on the card. Ink the card edges black.
For the vellum bouquet holder: Cut a 3 1/2" white vellum square and place it on point. Find the middle of the top right edge and mark it with a pencil. Repeat for the top left edge. Fold the right side in from the bottom center point to the point marked on the right. Repeat for the left side. Fold the left flap tip outward. Repeat for the right side. Glue the bouquet holder angled on the bottom right side of the card as shown.
For the stamped flowers and foliage: Stamp the base image of the large rose on black cardstock with VersaMark™ ink. Sprinkle with white embossing powder and tap off the excess. Emboss with the heat gun. Stamp the middle image with VersaMark™ onto the first embossed image. Sprinkle with silver embossing powder and tap off the excess. Emboss with the heat gun. Stamp the third image onto the embossed images with VersaMark™. Sprinkle with black embossing powder and tap off the excess. Use the paintbrush to remove any stray black powder. Emboss with the heat gun. Repeat this technique for a total of 3 large roses and 3 small roses.
Trim around the edges of each rose for a thin black border. Stamp and emboss 4 vine/leaves silver, and 3 sprigs white, all on black cardstock. For the 2 pairs of leaves, emboss the base image black on black cardstock, and emboss the second image white. Cut out the leaves, vines and sprigs, leaving a thin black border. Cut thin strips of Silver Linen paper for flower stems and glue to the back of each rose. Set 1 small rose, 1 silver vine/leaves, and 1 white sprig aside for the inside. Arrange the remaining roses and foliage on the top of the bouquet holder, layering with foam tape as shown.
Finish the front: Cut a 1 1/2"x3/4” white rectangle and trim the right corners for a tag. Mat on black with thin borders. Stamp “Hello” on the center of the tag and emboss it black. Glue the tag angled on the bouquet holder. Use 1/2" wide white/black dots ribbon to tie a bow. Zot™ the bow near the tag as shown.
For the vellum bouquet holder: Cut a 3 1/2" white vellum square and place it on point. Find the middle of the top right edge and mark it with a pencil. Repeat for the top left edge. Fold the right side in from the bottom center point to the point marked on the right. Repeat for the left side. Fold the left flap tip outward. Repeat for the right side. Glue the bouquet holder angled on the bottom right side of the card as shown.
For the stamped flowers and foliage: Stamp the base image of the large rose on black cardstock with VersaMark™ ink. Sprinkle with white embossing powder and tap off the excess. Emboss with the heat gun. Stamp the middle image with VersaMark™ onto the first embossed image. Sprinkle with silver embossing powder and tap off the excess. Emboss with the heat gun. Stamp the third image onto the embossed images with VersaMark™. Sprinkle with black embossing powder and tap off the excess. Use the paintbrush to remove any stray black powder. Emboss with the heat gun. Repeat this technique for a total of 3 large roses and 3 small roses.
Trim around the edges of each rose for a thin black border. Stamp and emboss 4 vine/leaves silver, and 3 sprigs white, all on black cardstock. For the 2 pairs of leaves, emboss the base image black on black cardstock, and emboss the second image white. Cut out the leaves, vines and sprigs, leaving a thin black border. Cut thin strips of Silver Linen paper for flower stems and glue to the back of each rose. Set 1 small rose, 1 silver vine/leaves, and 1 white sprig aside for the inside. Arrange the remaining roses and foliage on the top of the bouquet holder, layering with foam tape as shown.
Finish the front: Cut a 1 1/2"x3/4” white rectangle and trim the right corners for a tag. Mat on black with thin borders. Stamp “Hello” on the center of the tag and emboss it black. Glue the tag angled on the bouquet holder. Use 1/2" wide white/black dots ribbon to tie a bow. Zot™ the bow near the tag as shown.