Vintage Santa Double-M Christmas Card
For the card front: Cut 4"x5 7/8" Santa Baby tan border paper with the border along the top and glue centered on the front. Punch out the die cuts shown on the front and remove the nibs. Cut out the “ho, ho, ho…” greeting and mat on gray cardstock with 1/16" borders.
Cut a 3 1/8" length of the circles border and glue to the front at the lower left. Glue the large ornament frame and the greeting as shown. Glue the black circle overlapping the greeting at the upper right, then foam tape the remaining die cuts and place Dazzles™ as shown.
For the inside: Cut 4"x5 7/8" Santa Baby tan border paper with the ornaments in the upper left corner. Glue centered on the first inside panel. Cut out the “holiday cheer” label and glue at the lower right. Punch out a holly die cut, remove the nibs, and glue over the left end of the label.
Trace the inside paper pattern and cut two from Santa Baby black/green paper. Glue centered on the second and third inside panels. Cut two 7/8"x3 3/8" and two 1 3/8"x3 3/8" Santa Baby green snowflakes papers. Glue to the appropriate center panels.
Punch out the die cuts shown on the second and third inside panels and remove the nibs. Glue the red swirls to the upper left and lower right opening corners, then glue a circle die cut on each. Glue the ornament die cuts to the center panels as shown, trimming the hangers to fit. Cut the ribbon in thirds, then tie a knot in each. Trim the ends, then glue one to each swirl.
Cut 4"x5 7/8" Santa Baby tan border paper from the upper edge and glue centered on the inside fourth panel. Cut out the “sending you a little…” greeting and glue to the panel, 5/8" from the bottom.
Punch out the die cuts shown and remove the nibs. Glue the holly to the sentiment at the lower right. Glue the large ornament hanging from the upper edge 3 5/8" from the top and 1/8" from the fold. Trim off the excess hanger.
Glue the hanger from the large ornament to the panel, 7/8" from the right edge and extending ¾" down from the top. Glue the black ornament over the hanger end, then trim off any excess hanger. Glue the remaining knotted ribbon to the upper edge of the black ornament and place Dazzles™ as shown.
Cut a 3 1/8" length of the circles border and glue to the front at the lower left. Glue the large ornament frame and the greeting as shown. Glue the black circle overlapping the greeting at the upper right, then foam tape the remaining die cuts and place Dazzles™ as shown.
For the inside: Cut 4"x5 7/8" Santa Baby tan border paper with the ornaments in the upper left corner. Glue centered on the first inside panel. Cut out the “holiday cheer” label and glue at the lower right. Punch out a holly die cut, remove the nibs, and glue over the left end of the label.
Trace the inside paper pattern and cut two from Santa Baby black/green paper. Glue centered on the second and third inside panels. Cut two 7/8"x3 3/8" and two 1 3/8"x3 3/8" Santa Baby green snowflakes papers. Glue to the appropriate center panels.
Punch out the die cuts shown on the second and third inside panels and remove the nibs. Glue the red swirls to the upper left and lower right opening corners, then glue a circle die cut on each. Glue the ornament die cuts to the center panels as shown, trimming the hangers to fit. Cut the ribbon in thirds, then tie a knot in each. Trim the ends, then glue one to each swirl.
Cut 4"x5 7/8" Santa Baby tan border paper from the upper edge and glue centered on the inside fourth panel. Cut out the “sending you a little…” greeting and glue to the panel, 5/8" from the bottom.
Punch out the die cuts shown and remove the nibs. Glue the holly to the sentiment at the lower right. Glue the large ornament hanging from the upper edge 3 5/8" from the top and 1/8" from the fold. Trim off the excess hanger.
Glue the hanger from the large ornament to the panel, 7/8" from the right edge and extending ¾" down from the top. Glue the black ornament over the hanger end, then trim off any excess hanger. Glue the remaining knotted ribbon to the upper edge of the black ornament and place Dazzles™ as shown.
